ICR article draft Best mill practice and protection
水泥 葛大海 2015-08-01
广告
Sintered cast grinding rolls are gaining greater prominence by cementmill maintenance operators, asthey do not require intermediate hard facing repair. On the other hand, some producers have been reverting to regular hard facing of mill tyres and table liners, as breakage and abnormal loss of profile is often observed on sintered cast grinding rolls. This can result in a substantial lossof throughput and an increase in power consumption compared to similar output of grinding media by Ni-Hard castings.
Analysis provided in this article looksat how both types of castings can be intelligently applied, by keeping in mind the basic objective of achieving maximum plant availability and rated mill capacity throughput.
Myth or fact?
Sintered cast rolls are non-weldable?
Myth. Where minimum sinter materialis still visible, a small amount of surface preparation will enable welding to be carried out which could potentially increase working life by 6000-8000h – resulting in substantial savings for the plant. A successful trial at a South African cement plant has already demonstrated such encouraging results. The alternative is to replace the sintered cast table liners.
Complete hardfacing of sintered castings is not possible?
Myth. With the use of gauging flux cored wires and air gauging, a clean surface can be almost be achieved, which is suitable for hardfacing. Therefore, a number of welded repairs can be carried out.
There is no loss of profile in sintered cast?
Myth. The regular interaction with plant
Many arguments have been put forward in terms of best practice for maintaining mill grinding components. The two main solutions are hardfacing and sintered cast grinding rolls and table liners. However, it is not always clear when a cement plant should weld or when to simply replace components. By dispelling some common maintenance assumptions, this article how both types of castings can be applied to ensure best mill availability.
Figure 1: worn-out sintered cast table lines
WELDING & REPAIR
Figure 2: repaired by welding for additional life
operation and maintenance engineers suggest that there is a loss of profile after a year or between 5000-6000 working hours. Plant personnel can be faced with a dilemma since they can neither repair the roller profile to restore optimum
grinding efficiency nor replace the rolls as they are not worn enough. In such cases, selection on the basis of loss of sinter from the contact surface, hardfacing can be considered by adapting partial gauging onsite and then repairing the castings.
DECEMBER 2013 ICR XX
WELDING & REPAIR
Best practice study
One collaborative study undertaken by a hardfacing services provider and a cement plant maintenance team found the following measures enabled best mill availabiity:
Use Ni-Hard casting primarily for slag and clinker grinding, due the higher abrasive nature of both these materials Hi carbon Ni-Hard casting are best.
The reduction in profile was found to
be gradual and can be repaired while maximum life and throughput can be achieved with very low wear of less than 1g/t.
Sinter casts are good for raw mill
and coal mill grinding components. Throughput should be monitored closely and selective hardfacing be carried out to recover grinding efficiency.
Before throwing any castings, sintered or Hi carbon cast iron, consideration should be given to the saving resources given the costs involved in making new purchases. Even casting that has been
About the authors...
Abhijit Dhodapkar has worked closely with various Indian cement plants during his tenure as managing director of UK–MNC dealing in onsite hardfacing. As chairman of his new venture, FerroClad solutions, he is working with his Chinese counterparts on new collaborations using the latest techniques to repair sinter cast grinding components for cement plants in India, Africa and Middle East.
Graham Hughes has served 27 years as workshop chief for repairing grinding components. He is now general manager of Chinese Flux Cored Wire Manufacturing and Services Company, Beijing, Open Arc Welding Alloys.
Sinter casts are good
for raw mill and coal mill grinding components. However, throughput should be monitored closely and selective hardfacing can be carried out to recover grinding efficiency.
worn out up to 45mm on radius can be hardfaced with a close study of the best profile during the lifecycle of the casting. ? Losses in power consumption during and after the loss of the roll profile
need to be monitored closely so that
an informed decision can be made
and backed by efficient data collection management.
广告
相关资讯
2026年03月15日海螺水泥企业采购招标项目报告
水泥 03-16
2026年02月10日海螺水泥企业采购招标项目报告
水泥 02-11
存在违法违规问题 山东多家水泥、混凝土质量检验机构被通报
水泥 02-10
2026年01月30日天山材料企业采购招标项目报告
水泥 01-31
2026年01月16日海螺水泥企业采购招标项目报告
水泥 01-17
2025年12月04日海螺水泥企业采购招标项目报告
水泥 12-05
2025年11月21日海螺水泥企业采购招标项目报告
水泥 11-22
2025年11月11日天山材料企业采购招标项目报告
水泥 11-12
2025年11月02日海螺水泥企业采购招标项目报告
水泥 11-03
2025年10月19日天山材料企业采购招标项目报告
水泥 10-20
2025年10月10日海螺水泥企业采购招标项目报告
水泥 10-11
2025年09月30日海螺水泥企业采购招标项目报告
水泥 10-01
2025年08月14日海螺水泥企业采购招标项目报告
水泥 08-15
2025年08月01日海螺水泥企业采购招标项目报告
水泥 08-02
2025年07月25日海螺水泥企业采购招标项目报告
水泥 07-26
2025年07月15日海螺水泥企业采购招标项目报告
水泥 07-16
2025年07月11日海螺水泥企业采购招标项目报告
水泥 07-12
2025年06月20日海螺水泥企业采购招标项目报告
水泥 06-21
2025年06月11日海螺水泥企业采购招标项目报告
水泥 06-12
2025年06月08日海螺水泥企业采购招标项目报告
水泥 06-09
2025年05月24日海螺水泥企业采购招标项目报告
水泥 05-25
2025年05月10日海螺水泥企业采购招标项目报告
水泥 05-11
2025年05月05日海螺水泥企业采购招标项目报告
水泥 05-06
2025年04月21日海螺水泥企业采购招标项目报告
水泥 04-22
2025年04月13日海螺水泥企业采购招标项目报告
水泥 04-14
2025年03月27日海螺水泥企业采购招标项目报告
水泥 03-28
2025年03月25日海螺水泥企业采购招标项目报告
水泥 03-26
产业峰会|无锡锦华：辊压机立磨智能数字化耐磨堆焊
水泥 03-24
2025年02月15日海螺水泥企业采购招标项目报告
水泥 02-16
2025年01月14日海螺水泥企业采购招标项目报告
水泥 01-15
2025年01月07日海螺水泥企业采购招标项目报告
水泥 01-08
2024年12月25日海螺水泥企业采购招标项目报告
水泥 12-26
2024年12月21日海螺水泥企业采购招标项目报告
水泥 12-22
2024年11月27日海螺水泥企业采购招标项目报告
水泥 11-28
2024年11月11日海螺水泥企业采购招标项目报告
水泥 11-12
2024年11月06日海螺水泥企业采购招标项目报告
水泥 11-07
2024年09月20日海螺水泥企业采购招标项目报告
水泥 09-21
2024年09月10日海螺水泥企业采购招标项目报告
水泥 09-11
2024年08月26日天山材料企业采购招标项目报告
水泥 08-27
2024年08月04日海螺水泥企业采购招标项目报告
水泥 08-05
2024年07月01日海螺水泥企业采购招标项目报告
水泥 07-02
2024年06月18日天山材料企业采购招标项目报告
水泥 06-19
2024年06月15日海螺水泥企业采购招标项目报告
水泥 06-16
三态微孔催化剂在水泥行业的应用
水泥 10-17
为何要正确认识熟料中游离氧化钙含量的影响
水泥 09-22
浅析水泥生产过程影响水泥与外加剂适应性的因素
水泥 07-09
聚羧酸外加剂与水泥的相容性
水泥 07-09
矿渣水泥和普通硅酸盐水泥相比的差异和优缺点
水泥 06-06
装船小车运行中大臂抖动的解决方案
水泥 05-23
详解最主流的烟气脱硝技术
水泥 04-24
加载中...
放大
- 小
- 标准
- 大
- 特大
打开水泥网APP阅读
